Skip to content
vitscreen
Try for free

Setup guide

Install on the TV, enter the code, start playing

10 minutes with the remote. The app runs inside the TV itself; no extra device, cable or technician needed. The steps are for LG webOS Signage displays.

Create your account firstJump to the steps

LG webOS Signage display

Commercial (Signage) models with the SI Server setting. Setup is done with the remote; no separate player box is needed.

Internet connection

The TV only needs to reach https://api.vitscreen.com. No static IP or port forwarding required.

vitscreen account

Free trial: 15 days, 5 screens. Signing up takes a minute; no credit card required.

Four steps

Device in the panel, package on the TV, code on the screen

  1. Create a device in the panel

    Open the panel and choose Devices → Add device , then name the screen (e.g. "Kadıköy above the till"). On the card, a 6-digit pairing code appears; that's the code you'll enter on the TV. The code is unique to the device and stays valid until a TV connects.

  2. Enter the SI Server address on the TV

    On the remote, hold the Settings button, then type 8 0 8 0 and press OK: the service menu opens. SI Server Settings — open it and set the following:

    Application Launch Mode
    Local
    Application Type
    ZIP
    Fully Qualified Domain Name
    On
    Address (URL)
    https://vitscreen.com/dl/vitscreen-player.zip

    Menu names may differ slightly depending on the TV's firmware version; the heading to look for is always "SI Server".

  3. Install the package

    In the same menu, select Local Application Upgrade → Remote. The TV downloads the package (about 300 KB), installs it and restarts; on boot the vitscreen app opens full screen. From then on the app starts by itself every time the TV is switched on.

  4. Enter the code and start playing

    The screen shows "Ekranı Eşleştir" (Pair screen) with a code field below it. Enter the 6 digits from the panel using the remote's number keys; the moment the sixth digit is entered the TV connects itself. In the panel the device card goes online ; the scene you assigned to that device (or its group) is on screen within seconds.

Try it without a TV

The same player, in the browser

If you don't have a screen yet, open the player on your computer: vitscreen.com/player/. Enter the code from the panel; you'll see your scenes, group sync and price table without installing on a real TV.

  • Code entry and content flow are identical to the TV; there is no package difference
  • The browser tab also shows up as a device in the panel, and online/offline tracking works
  • For video wall sync, pair two tabs to the same group and put them side by side
  • When you're done, close the tab and delete the device card: your screen allowance is restored

If you get stuck

The six situations we see most in the field

The TV can't download the package
Check the address character by character; it must end in .zip. Older models may not recognize the https certificate chain — the same package is also served over plain http: http://vitscreen.com/dl/vitscreen-player.zip
Installation was triggered but the app didn't open
Select Local Application Upgrade → Remote again and power the TV off and on. If that doesn't help, unplug the TV for 60 seconds and plug it back in: some models keep the old package cached.
"Geçersiz eşleştirme kodu" (invalid pairing code)
Is the code exactly the one shown in the panel? The code belongs to that device card; another device's code won't work.
"Bu kod zaten bir ekranda kullanılıyor" (code already in use on a screen)
The code was already connected to a TV. In the panel, choose "Unpair" on the device card: a new code is generated and the old TV loses access; enter the new code on this TV.
I replaced the TV / paired the wrong screen
Same path: Unpair → new code → enter it on the right TV. Content, group and schedule settings stay on the device card; only the physical screen changes.
The code screen came back on the display
The device was unpaired or deleted from the panel; the TV can no longer fetch content for that account. Get the new code from the panel and enter it again.
Still not solved? Write to us and include the TV model and the message you see on screen. For other questions, see the FAQ. For everything after the TV is connected, see the user guide.

Create your account, connect your first screen today

15 days, 5 screens, free. No credit card, no installation crew: a remote and ten minutes are enough.

Create account — 15 days freeSign in to the panel

Need an enterprise rollout, store migration or custom integration?